Boilers & hydronic heating
Commercial boiler repair, replacement, and preventive maintenance. Hydronic loop service, circulator pumps, expansion tanks, and combustion analysis. Seasonal startup and shutdown programs for federal heating plants.
Installation, repair, and preventive maintenance of HVAC and plumbing systems for federal and commercial facilities. Delivered through licensed mechanical and plumbing trade partners under CFG's broker/GC model, the same model that delivers our roofing and remediation work. CFG holds the prime, administers the compliance stack, and gives the government a single point of contract accountability.
Every scope is executed by licensed mechanical and plumbing contractors, permitted and inspected to state and local code. CFG verifies licensure, insurance, and crew qualifications before award, not after.
Construction-trade wage determinations verified per solicitation. Certified-payroll-ready crews. Fringe and H&W loaded into the pricing stack. No surprise wage exposure.
PM programs built to manufacturer service intervals and delivered on recurring CLINs. Documented service logs, filter and belt schedules, and combustion checks a COR can audit.
One prime, one POC, one invoice. CFG owns contract administration, scheduling, and closeout so the government never has to chase a mechanical sub and a plumbing sub separately.
Installation, replacement, repair, and preventive maintenance across the building mechanical and plumbing stack. Every scope below is delivered by licensed trade partners under CFG's prime contract.
Commercial boiler repair, replacement, and preventive maintenance. Hydronic loop service, circulator pumps, expansion tanks, and combustion analysis. Seasonal startup and shutdown programs for federal heating plants.
Commercial gas, electric, and heat-pump water heater installation and replacement. Tankless systems. Recirculation loops, mixing valves, and venting to code. Same-week replacement scheduling for failed units.
Air handler service and component replacement: motors, belts, bearings, coils, and dampers. Ventilation balancing coordination. Filter programs on recurring CLINs with MERV ratings to facility specification.
Rooftop unit, split-system, and unit-heater repair and replacement. Condensate management. Refrigerant work performed by EPA Section 608 certified technicians. Crane and curb coordination handled under the CFG prime.
Thermostat and zone-control replacement, control-board swaps, and sequencing repairs. Coordination with facility BAS/EMS points of contact where building automation is in place.
Commercial toilet, urinal, lavatory, flushometer, and faucet repair and replacement. ADA-compliant fixture upgrades. Building-portfolio fixture replacement programs scoped and phased around occupancy.
Domestic water, sanitary, and gas piping repair and replacement: copper, PEX, PVC, CPVC, and black iron. Leak isolation and repair. Re-piping scopes phased for occupied federal buildings.
Backflow-preventer testing, repair, and replacement by certified testers. Thermostatic mixing valves, pressure-reducing valves, and relief-valve service. Test documentation filed to water-purveyor requirements.
Drain cleaning, jetting, and camera inspection. Sewer-line spot repair. Grease-trap and interceptor service coordination. Documented before/after video for COR closeout.
Recurring PM CLINs across heating, cooling, and plumbing assets. Manufacturer-interval service schedules, documented logs, and deficiency reporting that feeds the facility's work-order system.
Break-fix response for no-heat, no-cooling, and active-leak events. Coordinated through the CFG line with licensed trade partners on call. Stabilize first, then scope the permanent repair.
Mechanical and plumbing scopes coordinated with roofing (curbs, penetrations, flashings), remediation (post-water-loss re-pipe), and janitorial lines where CFG is prime for multi-trade work. One contract, one closeout.
Need products, not services? Plumbing/HVAC parts, MRO, janitorial supplies, and fasteners are delivered through our affiliate, Proven Supply Group.
Federal mechanical and plumbing awards turn on licensure, wage compliance, and safety documentation. Every scope below maps to published standards.
Mechanical and plumbing work delivered by contractors holding current state and local licenses. Permits pulled and inspections passed on every scope requiring them. License documentation released with the capability packet.
Construction-trade wage determinations applied to all installation and repair scopes. Certified payroll submitted weekly. Prevailing-wage fringe loaded into the pricing stack.
Refrigerant recovery, charging, and disposal performed by EPA 608 certified technicians. Recovery logs and cylinder documentation maintained per EPA requirements.
OSHA 30 site-supervisor coverage. Lockout/tagout procedures on every mechanical scope. Hot-work permits coordinated with the facility. Confined-space protocols where sewer or mechanical-room access requires them.
General liability with federal-facility additional-insured endorsement. Excess/umbrella coverage to meet or exceed federal solicitation floor. Workers' compensation current.
Startup reports, test-and-balance coordination records, backflow test filings, and PM service logs delivered in COR-ready format. Warranty registrations completed at closeout.
Federal HVAC and plumbing opportunities CFG is positioned to compete for across the Colorado Front Range.
One-time replacement scopes at GSA PBS, VA, and DoD facilities. Design-spec verification, permitted installation, and startup documentation under a single prime contract.
Base-year-plus-options preventive maintenance for heating, cooling, and plumbing assets. Manufacturer-interval schedules, documented logs, and deficiency reporting on recurring CLINs.
Building-portfolio restroom fixture replacement and ADA-compliance upgrades. Phased around occupancy. Water-efficiency retrofits where the solicitation calls for them.
IDIQ and BPA task orders at Fort Carson, Peterson SFB, Buckley SFB, and Schriever SFB. Break-fix and small-project mechanical work with badging and access protocols handled by CFG.
Water-loss and fire-loss mechanical reconstruction coordinated with CFG's remediation line. One prime from mitigation through mechanical rebuild and closeout.
Priced for set-aside competition. 8(a) application in process. Licensed mechanical and plumbing trade partners under CFG teaming terms, documented and available for review.
Mechanical and plumbing work is won on licensure, wage compliance, and showing up when a boiler fails. We deliver it the same way we deliver roofing and remediation: licensed trade partners do the work, CFG holds the prime, and the contracting officer gets one accountable party and a documentation stack they can audit.
Tell us the facility, the equipment, and the period of performance. We return a capability brief with the licensed trade partner that would deliver the work within one business day.